425 Oak - Osmo UV Protection Oil Tints 3.0L

425 Oak - Osmo UV Protection Oil Tints 3.0L

£88.48
Add to Wishlist
Free shipping on orders over £30.00

Current Stock 87 - message us if more required.

Royal Mail Tracked 24 Delivery
We attempt to ship all orders within 24 hours on a Tracked Service with Royal Mail. If your order is urgent please message us before ordering for an estimated delivery date.
SKU: 425P

apple paygoogle paymasterpaypalvisashopify pay
Description
  • Highly water and dirt resistant
  • Contains active ingredients to protect the coating against mould, algae and fungal attack
  • Clear and transparent colours available
  • Microporous, penetrating finish which does not crack, peel or flake
  • No sanding necessary when topping up coating
  • Delays natural greying by 12 times in comparison to untreated wood

SURFACE PREPARATION
Wood surface must be clean, dry and frost-free (moisture content max. 20%). Ideally, surfaces are sanded no finer than a P120 grit grade of sand paper. Sanding to finer grades will reduce required absorbency.Osmo UV-Protection-Oil Exra is ready to use. Do not thin. Stir well using a flat stirring stick or spatula before use. If possible, and if the wood is an absorbent species, please apply the first coat to all sides before installation.Fresh wood containing natural wood ingredients /extractives (eg: Cedar, Larch, Teak, Mahogany or Iroko) are often less absorbent and need to weather off first before applying the product. Please refer to website ‘Suitability’ section for more details. Weathering helps ingredient rich wood become more absorbent and the wood finish adheres optimally. Weathering is also required if ingredient rich wood has been freshly sanded or renovated.

A coloured base coat is recommended, e.g. Natural Oil Woodstain. Coloured base coats can improve UV protection.For renovations, clean old microporous wood finishes thoroughly. De-grey any weathered bare wood with Osmo Wood Reviver Power-Gel before applying an Osmo exterior product.Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works. To maintain absorbency, avoid sanding surfaces finer than a P120 grit. Weather ingredient rich wood after sanding.The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces.Soft wood species like Pine or Spruce are more prone to blue stain, rot and insects. If desired, pre-treat these soft woods if possible on all sides with Osmo WR Base Coat.

METHOD OF APPLICATION
With Osmo Flat Brush or Osmo Microfibre Roller, apply thinly along the wood grain and spread well.Allow to dry for approx. 12 hours. Cooler temperatures, higher humidity levels or over application will delay drying. Once dry, apply the second coat thinly.When recoating colour treated surfaces, or for renovation works, one coat applied to the clean and dry surface is usually sufficient.

NOTE
Oils enhance and intensify the natural tone of wood (permanent wet effect).Depending on the degree of weathering, apply one coat of Osmo UV-Protection-Oil Extra to the cleaned and intact finish after approx. 3-4 years.Osmo UV-Protection-Oil is best suited to vertical structures whereby there is plenty of water run-off. For areas exposed to strong weathering, such as flat horizontals, weatherboard, post caps or window sills, please expect significantly shorter renovation intervals. Vertical elements mounted onto horizontal wood should have at least a 15 degree angle. Sharp edges must be rounded (radius > 2 mm).If the greying process has already begun, de-grey the surface with Osmo Wood Reviver Power Gel and refinish the dried surface with 2 thin coats of Osmo UV-Protection-Oil Extra.To achieve the UV protection factor 12, it is necessary to apply 2 thin coats of UV-Protection-Oil Extra. With only one coat on untreated wood, the life of the coating is significantly shorter.Using power washers will severely decrease the coverage of the finish and general or multi-purpose cleaners will increase the frequency of maintenance and recoating.

CARE
Regular Cleaning: Damp cleaning with Osmo Spray-Cleaner or diluted Osmo Decking Cleaner .Occasional Maintenance: If necessary, intensive cleaning and refreshing using Osmo Wood Reviver Power Gel or Osmo Gard Clean.Recoating: Simply re-apply one thin coat onto the clean and dry surface when signs of wear become visible.Transparent Colour Finishes: 8 colours in a Satin* finish (UV-Protection-Oil Tints)

Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)

Osmo UV Protection Oil Tints – 425 Oak (3.0L)

Osmo UV Protection Oil Tints 425 in Oak provides a natural, microporous finish that protects exterior wood from weathering and greying. This 3.0L tin is ideal for larger projects such as timber cladding, fencing, doors, windows, and garden buildings.


Formulated with natural oils and active UV filters, this tinted oil slows the greying process by reflecting harmful sun rays while enhancing the wood’s appearance with a subtle oak tone. The finish is water-repellent, breathable, and does not crack, peel, or flake.

Key Features:

• Size: 3.0 Litres

• Tint: 425 Oak – a natural oak-coloured tone

• Finish: Satin/matt, microporous

• Coverage: Up to 26m²/L per coat (depending on wood species)

• Application: Brush or roller

• Use on: Vertical exterior wood such as cladding, doors, windows, fences, and garden structures

• Benefits:

• UV-resistant

• Water-repellent

• Breathable

• No sanding required for future applications


Osmo UV Protection Oil is also ideal as a top coat over Osmo Colour finishes to increase durability and UV resistance.

From Our Blog

Barrettine Wood Protection Products

Barrettine Wood Protection Products

on

Barrettine wood protection products offer reliable solutions for both interior and exterior timber care. From woodworm treatment to UV-resistant finishes and nourishing oils, OakCrafts stocks a trusted range for DIY and trade use. Explore the full collection now.

Continue Reading
View All