Osmo UV Protection Oil Extra, Exterior Wood Finish, Tinted, 3L Matt

CLEAR PROTECTION FOR VERTICAL STRUCTURES

Highly water and dirt resistant
Environmentally friendly wood finish
Clear and transparent colour finishes available
Microporous, penetrating finish which does not crack, peel or flake
No sanding necessary when topping up coating
Delays natural greying by 12 times in comparison to untreated wood

Surface Preparation

Wood surface must be clean, dry and frost-free (moisture content max. 20%). Ideally, surfaces are sanded no finer than a P120 grit grade of sand paper. Sanding to finer grades will reduce required absorbency.

Do not thin. Stir well using a flat stirring stick or spatula before use. If possible, and if the wood is an absorbent species, please apply the first coat to all sides before installation.

 Fresh wood containing natural wood ingredients /extractives (eg: Cedar, Larch, Teak, Mahogany or Iroko) are often less absorbent and need to weather off first before applying the product. Please refer to website ‘Suitability’ section for more details. Weathering helps ingredient rich wood become more absorbent and the wood finish adheres optimally. Weathering is also required if ingredient rich wood has been freshly sanded or renovated.

A coloured base coat is recommended, e.g. Natural Oil Woodstain. Coloured base coats can improve UV protection. For renovations, clean old microporous wood finishes thoroughly. De-grey any weathered bare wood with Osmo Wood Reviver Power-Gel before applying an Osmo exterior product.

Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works. To maintain absorbency, avoid sanding surfaces finer than a P120 grit. Weather ingredient rich wood after sanding. The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces.

Soft wood species like Pine or Spruce are more prone to blue stain, rot and insects. If desired, pre-treat these soft woods if possible on all sides with Osmo WR Base Coat.

Method of Application

With Osmo Flat Brush or Osmo Microfibre Roller, apply thinly along the wood grain and spread well. Allow to dry for approx. 12 hours. Cooler temperatures, higher humidity levels or over application will delay drying. Once dry, apply the second coat thinly. When recoating colour treated surfaces, or for renovation works, one coat applied to the clean and dry surface is usually sufficient.

Note

Oils enhance and intensify the natural tone of wood (permanent wet effect). Depending on the degree of weathering, apply one coat of Osmo UV-Protection-Oil Extra to the cleaned and intact finish after approx. 3-4 years. Osmo UV-Protection-Oil is best suited to vertical structures whereby there is plenty of water run-off. For areas exposed to strong weathering, such as flat horizontals, weatherboard, post caps or window sills, please expect significantly shorter renovation intervals. Vertical elements mounted onto horizontal wood should have at least a 15 degree angle. Sharp edges must be rounded (radius > 2 mm). If the greying process has already begun, de-grey the surface with Osmo Wood Reviver Power Gel and refinish the dried surface with 2 thin coats of Osmo UV-Protection-Oil Extra. To achieve the UV protection factor 12, it is necessary to apply 2 thin coats of UV-Protection-Oil Extra. With only one coat on untreated wood, the life of the coating is significantly shorter.

Using power washers will severely decrease the coverage of the finish and general or multi-purpose cleaners will increase the frequency of maintenance and recoating. 

• For our Cast Iron Products - Cast Iron will rust if exposed to moisture or high humidity. To remove surface rust use wire wool and lightly coat with a furniture wax or oil. You can also paint this product with a suitable metal paint. All cast iron products are supplied with a light oil or wax coating to prevent rusting in transit, this can be removed with a cloth or white spirit.

• Screws & Fixings - Where required our products are supplied with wood screws, you may require alternate fixings depending on your wall type. Always consult a professional tradesman if you are unsure.